Five Key Points to Note When Using Solar Road Studs in Rainy and Snowy Weather

2024-09-28

0 views times

Share us:

As a new type of road traffic safety facility, solar road studs have been widely used in all types of roads at all levels. At night and in rainy weather, when visibility is poor, they can rely on the light they emit to significantly improve road visibility and nighttime driving safety. On clear nights, solar road signs fully receive sunlight during the day and have sufficient electricity, so the light at night will be brighter. However, if it is rainy, snowy, or cloudy, the solar road studs receive limited sunlight, and the converted electricity will also be reduced. In addition, the weather conditions are not good and the light is weak, so the role of solar road studs will inevitably be affected. So what precautions should be taken when using solar road studs in rainy and snowy weather?

1. Waterproof

Although the shell of the solar road stud is designed to be waterproof, it may still be damaged if exposed to rain and snow for a long time. Therefore, it is necessary to clean up the water and snow near the solar road stud in rainy and snowy weather. After rainy and snowy weather, the sealing and waterproof performance of the solar road stud should be checked in time to ensure that there is no water seepage, so as not to cause a short circuit and affect the normal use of the solar road stud.

2. Clean up the snow and ice in time

After snowing in winter, the snow on the surface of the road stud should be cleaned in time. Sharp objects should be avoided from scratching the surface of the solar panel to prevent scratches and affect its ability to absorb and convert solar energy. Maintain the lighting effect of the solar panel and ensure charging efficiency. Check whether the road stud is affected by freezing due to low temperature and affect the brightness, and clean up the frozen part in time.

3. Suitable installation location and stability

In rainy and snowy weather, the slippery road and water accumulation may increase the impact of vehicles on the road stud. Therefore, when installing solar road studs, a flat, clean, and well-drained road surface should be selected. At the same time, the road studs should be firmly attached to the road surface with suitable glue (such as epoxy resin glue) to increase their adhesion and prevent them from falling off due to wheel impact. In addition, during the installation process, it is necessary to ensure that the road studs fit closely with the road surface to avoid gaps and bubbles. It is also necessary to avoid glue residue on the surface of the solar panel to affect the light conversion.

4. Regular inspection and maintenance

In rainy and snowy weather, solar road studs may be subject to more challenges and wear. Therefore, it is recommended to inspect and maintain the road studs regularly. The inspection content includes, but is not limited to, the cleanliness of the solar panel, the reflective effect of the reflective surface, the stability of the road studs, and the normal operation of the circuit system. If problems are found, they should be handled and repaired in time to ensure the normal operation of the road studs.

5. Dynamic warning and visual effects

Solar road signs usually flash at a certain frequency in rainy and snowy weather to enhance their dynamic warning effect. This flashing effect can not only attract the driver’s attention but also improve the visibility and safety of the road. Therefore, during the installation and maintenance process, it should be ensured that the flashing function of the road studs is normal, and the flashing frequency and brightness should be adjusted according to actual needs.

In summary, when using solar road studs in rainy and snowy weather, special attention should be paid to waterproofing, inspection, and maintenance. Only by ensuring the normal operation of these aspects can the solar road studs be fully utilized in adverse weather conditions and improve road traffic safety. We are solar road studs manufacturer. Our products have been used in many countries around the world, providing protection for local road traffic safety. If you also need solar road studs, please contact us. We look forward to your cooperation.

info@nk-roadstud.com

+86-13602600950

Previous: Tips for choosing solar road studs: key factors to improve energy efficiency and safety

Next: Positive Impact of Solar Road Studs on Future Traffic Safety

Inquiry

If you have any question or comment, please contact us without hesitation. We will reply you as soon as possible.( * is required information)

*Name:; *Email:; Phone:; Company:; Country:; *Message:

Hot Products

NOKIN Amber Raised Solar Road Stud Light For Expressway NK-RS-A6-1

2020-05-18

Body material: Aluminum(GB-ADC12)+PC(Japan Brand)
Power supply: USA Brand High Efficient Solar Panel
Battery: NI-MH1.2V/600MAH; Lithium battery3.2V/500MAH(Made in Japan);
Resistance: >30T
LED Color: White, Yellow, Blue, Red, Green
Size: L125mm*W107mm*H26+50mm

Heavy Duty Solar Road Stud For Sale NK-RS-X5

2020-05-18

Body material: Casting Aluminium alloy +PC
Power supply: 5V/80MAH Mono crystalline silicon
Battery: Lithium battery3.2V/1000MAH
Resistance: >40T(can be installed in the middle of road)
LED Color: White, Yellow, Blue, Red, Green
Size: φ125*50mm

Round PC Solar Road Stud Light NK-RS-K1

2020-05-18

Body material: PC
Power supply: Solar panel(Monocrystalline 2.5V /0.2W)
Battery: NIMH 600MAH
Resistance: >20T(static)
LED Color: White, Yellow, Blue, Red, Green
Size: φ117*23mm

Ultra Thin PC Solar Road Stud Light For Road NK-RS-Q7

2020-05-18

Body material: PC
Power supply: High efficient solar panel(5V/60mA)
Battery: Lithium battery(3.2V/500mAh)
Resistance: 15T
LED Color: White, Yellow, Blue, Red, Green
Size: 114*90*11mm

Nokin Solar Road Stud For Sale NK-RS-D1

2020-05-18

Body material: Hi-pressure Casting Aluminium alloy
Power supply: Solar panel(monocrystalline 2.5V/0.2W)
Battery: NI-MH 1.2V/800MAH or lithium battery
Resistance: >20T(static)
LED Color: White, Yellow, Blue, Red, Green
Size: L104*W104*H20mm

Yellow Flashing Aluminum Raised Solar Cat Eyes Road Stud On Road NK-RS-A6

2020-05-18

Body material: Hi-pressure Casting Aluminium alloy
Power supply: Solar panel(Monocrystalline 2.5V /0.2W)
Battery: NI-MH1.2V/800MAH
Resistance: >20 Tons
LED Color: White, Yellow, Blue, Red, Green
Size: L123*W133*H22mm+55mm

Internally Illuminated Solar Pavement Levelled Markers Studs NK-RS-X6

2020-05-18

Body material: Aluminum Alloy+PC cover
Power supply: Solar panel(Monocrystalline 2.5V /120MA)
Battery: Lithium battery 1000MAH*3.2V
Resistance: >30 Tons
LED Color: White, Yellow, Blue, Red, Green
Size: Ф123*45mm

6 LED Embedded Solar Road Marker Light Supplier In China NK-RS-A10

2020-05-18

Body material: Cast Aluminum
Power supply: Solar panel(Monocrystalline 2.5V /0.2W)
Battery: NI-MH 1.2V/800MAH
Resistance: >30 Tons
LED Color: White, Yellow, Blue, Red, Green
Size: Ф120*50mm（bottom）
Ф135*50mm（upper）

Colorful Aluminum Solar Road Stud Light For Road NK-RS-A6-2

2020-05-18

Body material: Heavy duty casting aluminium
Power supply: Solar panel(monocrystalline 2.5V/0.2W)
Battery: NI-MH 1.2V/800MAH
Resistance: >20T(static)
LED Color: White, Yellow, Blue, Red, Green
Size: L129*W114*H23mm+53mm

China Aluminuim Solar Road Stud Light For Sale With Best Price NK-RS-T1

2020-05-18

Body material: Aluminum+PC
Power supply: Mono crystalline solar panel
Battery: NI-MH 1.2V/ 600mah(high temperature resistance);
Resistance: >20T(static)
LED Color: White, Yellow, Blue, Red, Green
Size: 125*43*30mm

Colorful Glass Solar Road Stud Cheap Price in China NK-RS-A7

2020-05-18

Body material: Tempered Glass/PC
Power supply: USA Brand High Efficient Solar Panel
Solar panel(Monocrystalline 2.5V /0.2W)
Battery: NI-MH1.2V/600MAH(high temperature resistance, made in China)
Lithum battery3.2V/500MAH(made in Japan)
Resistance: >20T
LED Color: White, Yellow, Blue, Red, Green
Size: φ112*56mm

Aluminium Solar Powered Road Studs For Sale NK-RS-A1

2020-05-15

Body material: Hi-pressure Casting Aluminium alloy
Power supply: Solar panel(monocrystalline 2.5V/0.2W)
Battery: NI-MH 1.2V/800MAH
Resistance: >20T(static)
LED Color: White, Yellow, Blue, Red, Green
Size: L104mm*W94mm*H20mm